Share on facebook
Share on pinterest
Share on twitter
Share on linkedin
A VPN is an essential component of IT security, whether you’re just starting a business or are already up and running. Most business interactions and transactions happen online and VPN

Shoelaces will suffer a lot of wear and tear every time we tie the shoelaces when we put our shoes on. Eventually, the shoelaces will wear out with use and they begin to break down in the aglet.

When the aglet is gone, the entire lace will come off and it will be impossible to thread the lace back through the eyelet.

Therefore, we need tips or aglet fixes when necessary. In this article, learn about how to fix an aglet and how to replace an aglet.

How to Get New Aglets / Shoelace Tips

When buying a new pair of shoes, you probably don’t think much of the plastic cap at the top of the shoelace. When you put on your shoes, these jellies can fall off, leaving your laces exposed.

Luckily, you can make your aglet using some basic crafting materials. Here’s how to get new aglets/shoelace tips for you.

1. Remove the old aglet

First of all, you need to remove the old aglet before replacing them. The aglets are made very strong by the manufacturer and they can stick to the shoelaces. So the removal is also somewhat difficult. If it’s difficult after several attempts, consider cutting (if the length is sufficient). You can use your hands if the aglet is plastic, pliers or tweezers if the aglet is metal.

2. Prepare the shoelace ends

Of course, you need to have the ends of the shoelaces broken and in need of repair. If the end of the shoelace is not neat, frayed, or the fabric is frayed.

What you need to do is make them connect. You can heat the terminal quickly with a lighter. Note that the fabric’s ashes will cause burns, so you need to be careful when using it.

Or you can use dry glue to glue the fibers together, but you should also use a support tool to avoid sticking your fingers together.

Or you can use scissors and cut away a bit of the frayed end, the fibers separating. The easiest way is to get them wet, roll them up, and stuff them in a new aglet.

3. Measure your shoelace width if needed

This is something that few people notice. Usually, new aglets are universally manufactured in series and certain sizes.

Some shoelaces will have a different size, so all you need to do is use a centimeter ruler to measure the width of the end of the shoelace.

This is necessary if you don’t want to buy a new aglet that doesn’t fit and has to be exchanged or even thrown away.

4. Place the aglet over the lace end

You just need to insert the end of the shoelace into the new aglet to fit the desired size. The simplest aglet is made of plastic, so you just need to use a dryer to shrink them and hold the shoelace tightly.

Metal aglets require more specialized tools to tighten. Choose an aglet that you like best and take care to get one that fits your shoelace exactly.

5. Cut the aglet end if needed. 

This is the final part to adjust to suit the aesthetic. If there are excess threads or the two ends of the aglet are not equal, cut them off for the best fit. If both match then you’ve got the perfect shoelaces.

5 Common Methods to Repair the Aglet / Shoelace End

Aglets are a small but very important part of shoelaces. Missing or damaged aglets can lead to real nuisances.

If you are looking for an alternative to buying aglet, you can use one of the following methods.

Here are some different instructions for creating a new aglet after it’s lost, broken, or after a shoelace is shortened. The methods below all use what is available in your home.

1. Glue and Thread Method

The glue and thread method is the simplest, fastest, and easiest to find necessary tools.

– Tools to prepare: glue (any glue will work, for example, the glue used for crafts, leather repair, furniture repair), thread (must have a certain strength), knife vertical paper, ruler, scissors.

– Steps to perform:

Step 1: Remove the old aglet if they interfere with the preparation for the new aglet. You can use a paper-knife to remove stubborn old aglet seeds.

Or you can use scissors to cut off the residue on the safety surface which will also help avoid cutting into the surface where you are working.

Step 2: Apply some glue on top of the peeled aglet end. Note that it should not be redundant and should be neat.

Step 3: Wrap the aglet end tightly with thick thread. Wrap one end of the thread around your finger.

Take the other end of the thread and start winding the thread around that end, starting about 1cm across from the frayed end & ending towards the tip.

Try to roll it as tight as you can. The tighter you wrap, the thinner the aglet end will be.

If you’re worried about leaving a spot, you can go back and cover up the missed spot. At this point, if the glue starts to drip, just wipe it and move on.

Step 4: Fix the two threads by tying both ends of the thread and let it dry for 10 minutes.

Step 5: Let’s make them neat. After the cream dries, simply use a brush to clean the dried glue and even out the color. Trim the tip a bit to make it look cleaner.

Step 6: Finally, check the aglet wrapper for loose fibers. It is possible that while wrapping you lose your hand and some loose threads or threads need to be glued down, cut, or reassembled.

Please remove any yarn and thread lose or glue down for an even look. This is also the final step to complete the fixation of the aglet with the glue and thread method.

2. Scotch Tape Method

The Scotch tape method is the fastest method of preparation and is also simple for aglet fixers.

– Tools to prepare: simply Scotch tape and you.

– Steps to perform:

Step 1: Remove the old jelly (if necessary) and take a piece of duct tape that is 2.5 times the circumference of the end of your frayed shoelace. The type of tape you use can make a big difference.

If you have thicker tape, you need to get a shorter piece of tape, which is 2 or 1.5 times the circumference of the end of the shoelace to be repaired.

Step 2: Place the tape under the end of the shoelace to be repaired and the end of the tape should be placed under the adhesive part of the shoelace facing up.

Carefully wrap the scotch tape around the end of the laces so that it creates a cylinder around the end of your frayed laces.

To wrap tightly, it is recommended to use a hard surface to roll and balance the tape before rolling.

Step 3: Check the scotch tape wrap. The adhesive tape must adhere well to the threads of the shoelace end. Avoid loose wrapping that quickly pulls the tape off the aglet.

If you can wrap tightly, the end should also wrap tightly for the best effect. If it doesn’t feel right, you can remove the bandage and try again.

Step 4: Cut the end if there is excess and you find it enough. Next, wrap both ends and compare them to see if they are equal.

You can then use scissors to cut the excess so they look the same. So you’ve got a new aglet.

3. Glue Method

This is the 3rd method that we want to mention to you – The glue Method. First, let’s find out which glue is the most suitable and can bring maximum benefit when you use it.

Which glue to choose?

The recommended option is to choose an acetone-based solvent such as “Tarzan’s Grip”, or “Britfix Balsa Cement”. This glue needs to be dry, hard, and waterproof.

You can tell by their look and smell – the acetone-based glue is clear and has a strong petrochemical smell.

NOTE: Adhesive manufacturers have health warnings about “prolonged skin contact”, so wear gloves if this is of concern. If accidentally caught, use acetone, thinner, or nail polish remover to clean up afterward.

– Tools to prepare: glue with hardness, dry and waterproof, scissors.

– Steps to perform:

Step 1: Remove the old aglet.

You can use scissors to cut off the old aglet (if needed). Just make sure you can use the shoelace the way you intend it to.

Step 2: Choose the right glue. See if the glues available for use in your home are suitable, if not, you need to find them.

You’ll need glue that’s strong enough, and waterproof, to help the end of your shoelace get through your eyelet.

A hot glue gun can work well for hardening the end of shoelaces. Fabric glue can work well to create a rubbery texture around the end of a shoelace.

Super glue is a great way to harden the ends of your shoelaces. A little tip for you: If the ends of your shoelaces are very frayed, you can carefully apply glue between the threads so they stick together.

Step 3: Apply glue to the aglet end of the shoelace. Try to apply glue with a special tool to be safest.

The way of brushing, dipping, or rolling glue and then smoothing is followed by many people. If your glue has an odor, choose a well-ventilated place.

Step 4: This step requires your dexterity. Roll, brush or use gloves to shape the laces into a circle to fit the eyelets of the shoe.

Shoelaces should be straight and smooth with all threads tightened together. If there are excess parts you can handle them with scissors.

Step 5: Let the shoelaces dry in normal conditions. Place the shoe on a high surface, avoiding contact with surrounding objects so that the tip of the shoelace can dry quickly.

You may need to wait 24 hours for some glues to cure before they are completely dry.

Step 6: Cut off excess laces if needed after the ends are dry. Sometimes the head just wants to come off even after applying glue.

All prepared enough for you to put the shoelaces in the eyelets, ready to go out.

4. Wax Method

The wax method has the same method and mechanism as the glue method.

– Tools to prepare: wax (candle wax), scissors.

– Steps to perform:

Step 1: Remove the old aglet. You can use scissors, similar to step 1 in the methods above.

The material we recommend for waxing is candle wax. So check to see if you have a white candle at your home. Or any candle color will do but if it is different from the color of the shoelaces, it may alter the color of your shoelace ends and may look slightly different.

Other materials:

A more durable “melting” solution is to use solder resin or sealing wax (wax used to make seals for dispatches or documents). Because both of these are harder, they usually need more heat to melt, and dry. Plus, they’re usually not available at home.

Step 2: Proceed to light the candle and put wax on the safe area. You should choose surfaces that are non-stick and do not melt easily when exposed to high temperatures.

Next, carefully dip the end of the shoelace in the wax and roll the end of the shoelace to cover the entire end. Note: the heat of the wax can cause minor burns so be careful and wear gloves.

Step 3: Allow the wax to absorb and dry on the aglet head for a period of 30 minutes to an hour. The wax will soak into the fabric and begin to dry, then continue to remove the end of the shoelace from the wax as it starts to look dry.

Step 4: Carefully shape the wax into a circle. As you do this, make sure the wax doesn’t get hot and start to dry and roll the end over a hard surface or carefully shape it with your fingers.

Pro tip: You can apply a small amount of turpentine on top of the aglet, then roll it between your fingers while it’s still warm to create a reasonably short-term jelly.

WARNING: Do not want to heat the threaded tip once it has waxed; the possibility of burning it is very dangerous! Instead, warm a flat knife and use that knife to mold the wax.

Step 5: Check that the wax has hardened and can be inserted through the eyelets. This shows the final result after the wax has been kneaded into a smooth finish.

Although candle wax is quite soft, it penetrates the fibers of the shoelace, making the finished aglet quite sturdy. If it’s ok then you’re done replacing an aglet.

5. Knot Method

If you do not have the tools for the above solutions or do not want to use them, you need an immediate solution.

This will be the best-suggested solution for you, that is you can tie a knot at the end of your shoe aglet.

This will make the end of the shoelace look fancier and prevent it from accidentally going through the eyelet.

Advantages & Disadvantages:

This method prevents knotting, as knots often don’t fit into the eyelet. While this method is cheap, easy, durable, and quite effective at preventing the ends of laces from fraying, the downside is that it shortens the laces.

Interestingly, back-lacing can become an advantage as children learn how to lace their shoes. Often they will pull the wire out of the eyelet.

This is helpful because it helps prevent those ends from accidentally being pulled through the knot (when tightening) or out of the eyelet (when loosening).

Conclusion

You know the phenomenon. No matter how hard you try, eventually, the little plastic tip at the end of your shoelace (aglet) will get brittle and over time, you’ll find yourself with a set of frayed laces.

You can do the classic trick of burning the ends with a match to keep the hairs in place, but that’s a temporary solution. So we have brought you the best solutions for fixing an aglet or replacing an aglet.

Hope this article “how to replace an aglet/ how to fix an aglet” will help you.

Florsheim Esquivel

Florsheim Esquivel

This is the brand that Florsheim partnered with the innovative George Esquivel. The purpose of the brand is an effort to return to those humble roots and continue the brand’s rich, longstanding reputation for quality, craftsmanship, and expertise.

Leave a Replay

About Me

This website has diverse reviews about shoes for you to choose from. It is including in 5 main product reviews that are sports shoes, work shoes, walking shoes, dress shoes, shoes general,… I think these article review in this website so enough information about shoe products beside they also provide the more buying guide and explore useful tips regarding shoes. They provide information about where to buy shoes, how much shoes, shoe resources, and why people should wear shoes?

 

Recent Posts

Follow Us

Weekly Tutorial

Sign up for our Newsletter

Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit